Revision as of 06:16, 19 March 2017

If you'd like to check how accurate your Treadmill is, here's the testing procedure. It's not as simple as some other approaches, but it provides a far more accurate result. This test evaluates the treadmill while you're running on it, so it includes any possible slowdown that occurs well your foot is in contact with the belt. I developed this procedure while testing the Stryd Footpod. I'd found that their Footpod is stunningly accurate outside, but seemed to be way off on the treadmill. The folks at Stryd investigated reports from various runners about problems on the treadmill, and they found that many treadmills vary in speed, slowing down when the runner is in contact with the belt. This is in addition to any other calibration problems a treadmill might have.

1 Equipment

Besides the treadmill, you'll need a camera capable of recording high speed video, sometimes referred to as "Slo-Mo video". An iPhone 6 or 7 works well, though there are other options. You'll need to place markers at regular intervals along the belt. I used round sticky labels from Amazon that are intended to be color coding dots. You need to measure the distance between the labels, and I used a standard steel rule. I put my phone on a tripod, though you could ask a friend to take the video for you instead.

2 Setup

Put the markers exactly the same distance apart. I chose 12 inches, and I'd suggest something similar as you need a distance small enough that you'll travel with your foot in continuous contact, but long enough that the frame rate will cause accuracy problems.

The distance between your last marker and your first won't be the same as all the others, so make them visually different. I put two markers side-by-side and different colors.

When you're done your treadmill should look something like this. I should probably have put my markers a little further from the edge so they are easier to see when the camera's looking sideways at the treadmill from a low angle.

3 Recording

The actual recording is fairly simple. I set up my phone so that it was looking sideways at the treadmill, and slightly above the belt. You need to be able to see when your foot is in good contact with the belt, and see the markers as they go by. You only need to record about a minute of travel, but make sure you let the treadmill get up to full speed. If you have a remote shutter release, you can record only when your speed has stabilized (I couldn't find my remote release when I shot my calibration video.)

4 Analyzing

I used Kinovea for analyzing the results. It's free, open source software, and you can find some more details at High Speed Video Analysis. I used Dropbox to transfer my video to my PC.

After opening Kinovea you'll see a directory navigating tree in the top left-hand corner. Find the directory that contains your video, and double-click on it to open the file.

Kinovea requires you to select a subset of your video for analysis, called the "working zone". Use the play button or click on the timeline to move to a useful starting point (red arrow). Then click on the "[" to mark the start of your working zone.

Play the video or skip along the timeline so you have a reasonable number of strides, then click on the "]" button. Your window should then look like this, with the timeline bar only having the selected window shown as a green line. There is a second timeline bar below for the working zone.

Drag a stopwatch onto the video. I used the stopwatch as a reference point, so I put it with the left edge of the stopwatch aligned with the right edge of one of the markers.

Right click on the stopwatch and started. Nothing will happen to me, but the stopwatch will count time for each frame that passes.

Use the frame advance button to slowly play the video until the next marker is lined up. Here you can see that it took 0.112 seconds for the treadmill belt to move 12 inches. I'd recommend repeating this several times to check your getting a stable reading. You have to right click and delete the stopwatch as there does not appear to be a reset function. Make sure you're only recording the time when your foot is in contact with the belt.

5 Calculations

The calculation of pace is fairly simple, and I used Excel. If your timings vary from sample to sample, then you need to average them out. In my testing, I got exactly the same time for each sample which made things easier. I calculated the number of inches per second the belt was moving at by dividing the distance (12 inches) by the time (0.112 seconds), giving me 107 inches/second. This is then converted to miles/hour by dividing by 17.6, giving me 6.087 MPH. Sadly, my treadmill was set to 7.0 MPH, so it's a long way off!