Difference between revisions of "DIY Hypoxicator"
From Fellrnr.com, Running tips
User:Fellrnr (User talk:Fellrnr | contribs) |
User:Fellrnr (User talk:Fellrnr | contribs) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[File:Finished Hypoxicator.JPG|right|thumb|500px|The finished DIY hypoxicator.]] | [[File:Finished Hypoxicator.JPG|right|thumb|500px|The finished DIY hypoxicator.]] | ||
| − | The heart of my [[DIY Altitude Training]] system is the 'hypoxicator'. The principle of this | + | The heart of my [[DIY Altitude Training]] system is the 'hypoxicator'. The principle of this [[Altitude Training]] system is that you rebreathe your exhaled air, and each time you do so the oxygen level drops. This creates air that has less oxygen, which simulates high altitude. However, you can't simply [[Breathing| breathe]] into a bag because as the oxygen level drops, the carbon dioxide levels rise. This rise in CO2 will cause you to breathe deeper and faster, leading to dramatic panting without any drop in your blood oxygen level ([[SpO2|SpO<sub>2</sub>]]). To overcome this problem, your breath must go through a CO2 scrubber, which is the function of the hypoxicator. This hypoxicator is essentially a box filled with a chemical CO2 scrubber, plus attachments for the breathing hoses and filters to keep the scrubber in the box. I made mine for less than $20 plus the cost of the CO2 scrubber. |
=Tools and materials needed= | =Tools and materials needed= | ||
You will need the following: | You will need the following: | ||
| − | * '''Box'''. An air tight box, which should be about a pint/half liter in size. The box should be clear, as the CO2 scrubber changes color when it needs replacing. Ideally the lid of the box should fit into the box rather than creating a dome above so that there is no air gap above the CO2 scrubber. This [http://www.amazon.com/Felli%C2%AE-Flip-Tite-Square-Canister/dp/B00936VDVC Flip-Tite container] is ideal and is the one I use. | + | * '''Box'''. An air tight box, which should be about a pint/half liter in size. The box should be clear, as the CO2 scrubber changes color when it needs replacing. Ideally the lid of the box should fit into the box rather than creating a dome above so that there is no air gap above the CO2 scrubber. This [http://www.amazon.com/Felli%C2%AE-Flip-Tite-Square-Canister/dp/B00936VDVC Flip-Tite container] is ideal and is the one I use. The box I use is approximately 3.5 x 3.5 x 2.5 inches, or 8cm x 8cm x 6cm in size. |
| − | * '''Hose connector'''. I used some viral filters cut in half, but you might be able to use a plumbing connector. (You will need viral filters for the overall | + | * '''Hose connector'''. I used some viral filters cut in half, but you might be able to use a plumbing connector. (You will need viral filters for the overall altitude training system.) I got my filters from [http://www.allegromedical.com/respiratory-therapy-c534/main-flow-bacterial-viral-filter-p547468.html?utm_expid=44248-8 Allegro Medical] for around $3 each. |
* '''Air Filter'''. I used parts of an air conditioning filter to stop the scrubber going into the holes for the hoses. I think you could use other materials, such as open cell foam. | * '''Air Filter'''. I used parts of an air conditioning filter to stop the scrubber going into the holes for the hoses. I think you could use other materials, such as open cell foam. | ||
* '''Drills'''. You will need to cut a hole into the box that's about an inch/2cm or so wide. The box I used is polycarbonate, which is tough, but you need to cut it carefully. | * '''Drills'''. You will need to cut a hole into the box that's about an inch/2cm or so wide. The box I used is polycarbonate, which is tough, but you need to cut it carefully. | ||
* '''Saw'''. I cut the viral filters in half with a hacksaw designed for metal and it worked quite well. A vice to hold the viral filter still is handy. | * '''Saw'''. I cut the viral filters in half with a hacksaw designed for metal and it worked quite well. A vice to hold the viral filter still is handy. | ||
* '''Glue'''. It's hard to glue polycarbonate, but I found that if you sanded the parts, an epoxy resin worked well and created an air tight seal. If you use other glues, you may need some type of sealant. | * '''Glue'''. It's hard to glue polycarbonate, but I found that if you sanded the parts, an epoxy resin worked well and created an air tight seal. If you use other glues, you may need some type of sealant. | ||
| − | * '''CO2 scrubber'''. The CO2 scrubber is a consumable as it uses a chemical reaction to absorb the CO2. The scrubber will change to a | + | * '''CO2 scrubber'''. The CO2 scrubber is a consumable as it uses a chemical reaction to absorb the CO2. The scrubber will change to a purple color when it's used up, and the latest generation scrubbers have a permanent color change. |
| + | ** I now use "Amsorb Plus" and buy it in 1Kg bags. I got [http://www.hullanesthesia.com/p/966/amsorb-plus-co2-absorbent-1kg-bag 12x 1Kg bags from Hull Anesthesia]. It's more expensive than the Soda Lime, costing $155 for the 12 bags, plus shipping. The Amsorb Plus lasts for longer, and it's claimed to be more economical than other scrubbers. | ||
| + | ** I was using 'JorVet J-553 Soda Lime', produced by Jorgensen Laboratories which I get from shopmedvet.com. They tend to change their URLs so you may have to search for 'soda lime' on their site. Each 3 pound bag is $7.80 (plus $10 shipping per order), and each bag tends to last me for a few weeks. | ||
| + | ** There is an interesting write up of the different scrubbers at http://www.armstrongmedical.net/absorbent/amsorb-plus/amsorb-plus | ||
=Construction= | =Construction= | ||
The steps to construct the Hypoxicator are reasonably simple. | The steps to construct the Hypoxicator are reasonably simple. | ||
| Line 25: | Line 28: | ||
[[File:With air con.JPG|none|thumb|500px]] | [[File:With air con.JPG|none|thumb|500px]] | ||
==Fill with CO2 scrubber== | ==Fill with CO2 scrubber== | ||
| − | Just fill the box with CO2 scrubber and close the top. Store the hypoxicator in a sealed plastic bag when not in use. | + | Just fill the box with CO2 scrubber and close the top; you're all done. Store the hypoxicator in a sealed plastic bag when not in use. |
[[File:DIY Hypoxicator.JPG|none|thumb|500px]] | [[File:DIY Hypoxicator.JPG|none|thumb|500px]] | ||
| + | =Feedback= | ||
| + | If you make your own DIY Hypoxicator, please let me know how you get on. | ||
Latest revision as of 05:59, 3 July 2014
The heart of my DIY Altitude Training system is the 'hypoxicator'. The principle of this Altitude Training system is that you rebreathe your exhaled air, and each time you do so the oxygen level drops. This creates air that has less oxygen, which simulates high altitude. However, you can't simply breathe into a bag because as the oxygen level drops, the carbon dioxide levels rise. This rise in CO2 will cause you to breathe deeper and faster, leading to dramatic panting without any drop in your blood oxygen level (SpO2). To overcome this problem, your breath must go through a CO2 scrubber, which is the function of the hypoxicator. This hypoxicator is essentially a box filled with a chemical CO2 scrubber, plus attachments for the breathing hoses and filters to keep the scrubber in the box. I made mine for less than $20 plus the cost of the CO2 scrubber.
Contents
1 Tools and materials needed
You will need the following:
- Box. An air tight box, which should be about a pint/half liter in size. The box should be clear, as the CO2 scrubber changes color when it needs replacing. Ideally the lid of the box should fit into the box rather than creating a dome above so that there is no air gap above the CO2 scrubber. This Flip-Tite container is ideal and is the one I use. The box I use is approximately 3.5 x 3.5 x 2.5 inches, or 8cm x 8cm x 6cm in size.
- Hose connector. I used some viral filters cut in half, but you might be able to use a plumbing connector. (You will need viral filters for the overall altitude training system.) I got my filters from Allegro Medical for around $3 each.
- Air Filter. I used parts of an air conditioning filter to stop the scrubber going into the holes for the hoses. I think you could use other materials, such as open cell foam.
- Drills. You will need to cut a hole into the box that's about an inch/2cm or so wide. The box I used is polycarbonate, which is tough, but you need to cut it carefully.
- Saw. I cut the viral filters in half with a hacksaw designed for metal and it worked quite well. A vice to hold the viral filter still is handy.
- Glue. It's hard to glue polycarbonate, but I found that if you sanded the parts, an epoxy resin worked well and created an air tight seal. If you use other glues, you may need some type of sealant.
- CO2 scrubber. The CO2 scrubber is a consumable as it uses a chemical reaction to absorb the CO2. The scrubber will change to a purple color when it's used up, and the latest generation scrubbers have a permanent color change.
- I now use "Amsorb Plus" and buy it in 1Kg bags. I got 12x 1Kg bags from Hull Anesthesia. It's more expensive than the Soda Lime, costing $155 for the 12 bags, plus shipping. The Amsorb Plus lasts for longer, and it's claimed to be more economical than other scrubbers.
- I was using 'JorVet J-553 Soda Lime', produced by Jorgensen Laboratories which I get from shopmedvet.com. They tend to change their URLs so you may have to search for 'soda lime' on their site. Each 3 pound bag is $7.80 (plus $10 shipping per order), and each bag tends to last me for a few weeks.
- There is an interesting write up of the different scrubbers at http://www.armstrongmedical.net/absorbent/amsorb-plus/amsorb-plus
2 Construction
The steps to construct the Hypoxicator are reasonably simple.
2.1 Cut the viral filters
The viral filters are cut in half so that you have an attachment for the breathing hose.
2.2 Cut holes in the box
I used a small drill to create a pilot hole, then used the hole cutter. You need to cut polycarbonate slowly and gently to prevent it either melting or cracking. Cut the holes closer to the bottom than shown.
2.3 Glue the viral filters in place
I used an epoxy resin, which worked quite well, but you need to sand the contact surface of the box to create some roughness the resin can adhere to. I tried to glue both ends on at the same time, which was a mistake; glue one, then the other when the first is set. You will need an air tight seal, so use plenty of resin. I had to go back a few times to seal holes I'd missed.
2.4 Add the air filter
Cut some air filter material to size and cover the open holes.
2.5 Fill with CO2 scrubber
Just fill the box with CO2 scrubber and close the top; you're all done. Store the hypoxicator in a sealed plastic bag when not in use.
3 Feedback
If you make your own DIY Hypoxicator, please let me know how you get on.
