8,160
edits
Changes
no edit summary
Runn is a small sensor that you add to a treadmill to measure speed. The idea is It uses two optical sensors that measure how long it transmits the takes for a reflective sticker to pass between them to calculate speed . This is then transmitted using a protocol that can be received by Bluetooth or Ant+ to various watches and applications, including zwift.com. =The Big Problem=There is a downside to Runn you need to be aware of; it works. This means that Runn is like the red pill in The Matrix, who revealing how far and how fast you're actually sell running on your treadmill. The chances are, this is a lot slower than your treadmill claims, which can be rather depressing. I've not seen any broad testing of treadmill accuracy, but it's common for people to find their treadmill is reading 2.5-6% faster than it should, and mine it off by 10+% (though I've jacked up the Runn sensorback to run downhill. Most treadmills won) I think it't transmit the right protocol, s vital to know your pace and distance for training so until now you either need to use a Footpod or rely on 're not surprised when you move into the internal accelerometer in your sports watchoutside world. =How it Works=The sensor works by using 2 optical sensors that look for stickers on the treadmill belt. It measures the time it takes for the sticker to move from one sensor to the next, which should give a fairly accurate measure of the treadmill belt speed at the time the sticker is under the sensor. Unfortunately=Protocols=Most treadmills won't transmit a protocol that can be used by a watch or smart phone app, so until now you either need to use a Footpod or rely on the internal accelerometer in your sports watch. The Runn will use either Ant+ or Bluetooth to emulate a speed sensor. This should be supported by most watches, as well as apps like Zwift on a smart phone. There is support for FE-C (Fitness Equipment Control), but few watches will support that. The FE-C protocol will transmit incline, which would be nice to capture, and it would be possible for this to be added on the newer Garmin watches using [[Connect IQ]]. =Accuracy=One concern with the Runn is that's where is measures the problem liesspeed continually, as but the speed of most treadmill belts is not continuous, but and varies with your foot strike. When your foot lands on the treadmill belt, the belt slows up quite a bit, then as the treadmill compensates it speeds up during the stance phase, and then when your airborne the belt will speed up even more. I exchanged emails with North Pole Engineering, and confirmed that their sensor will be taking the average belt speed, which will result in an error. <br/><br/>Consider my treadmill, where I've performed [[Treadmill Calibration]]. I've performed used High Speed Video, with frame by frame measurements across multiple foot strikes to gather actual performance figures. When my treadmill is set to 8 MPH, the average speed of the belt when I'm running is actually 7.17 MPH, which is 10.4% slow, which is really bad. This The average represents a minimum speed just after foot strike of 6.6 MPH, rising to a maximum speed of 7.3 MPH just before toe off. While I'm in flight, the speed rises further to 7.6 MPH just before foot strike. The average belt speed while my foot is in contact is 7.06 MPH, which is 1.5% slower than the average belt speed, which is what Runn measures. Does that matter? Well, if you were marathon training and Runn said you'd run 20 miles at 9:00 min/mile pace, you'd have actually run 19.7 for 9:08, which is pretty close. When you consider the variation in speed during contact, it's a fair estimate. On the other hand, if you'd believed my treadmill, when you thought you'd run 20 @ 9:00 you'd have only run 18.1 at 9:56 pace! A bigger concern would be the measurement points coinciding with a particular point in your foot strike, which could result in readings anywhere between the min and max speeds. Adding more marker stickers may help with that. My plan is to buy one of the sensors and try it out. <br/><br/>So, is it worth it? Well, the sensor is fairly cheap, listing at $99 at the time of writing, and it's almost certainly more accurate than your treadmill display, and more accurate than the accelerometer in your running watch. I'm expecting it to be more accurate than a standard [[Footpod]], and while [[Stryd]] is remarkably accurate outdoors, Stryd tends to struggle on a Treadmill due to the speed variations. Runn is also a convenient approach, and if you took the time to calibrate your treadmill, you could add the calibration factor into most running watches. The Runn also measures incline, though I'm not sure what software would support that measurement. I'd love to have incline data from my treadmill runs, but it may require a custom [[Connect IQ]] data field. <br/><br/>
Below is the data from a few steps on my treadmill. The orange markers show when my foot is in contact with the belt. I've assumed that any contact, no matter how slight counts as contact, so flight time is low.
[[File:Treadmill Multistrde.jpg|center|thumb|300px|]]
=How To Use Runn=
Runn is reasonably easy to set up; just follow the instructions. You stick the reflectors onto the belt, which probably requires you to clean the patches to ensure they stick. You have to make sure the stickers are all the same offset from the edge of the belt, and then align the sensor box with the stickers. You can set the Runn to the show the same as your treadmill, but that defeats the purpose somewhat. The issue for some runners will be that you can't move the Runn sensor to different treadmills if you use a Gym.
=Is It Worth It?=
So, is it worth it? Well, the sensor is fairly cheap, listing at $99 at the time of writing, and it's almost certainly vastly more accurate than your treadmill display, and more accurate than the accelerometer in your running watch. It's more accurate than a standard [[Footpod]], and while [[Stryd]] is remarkably accurate outdoors, Stryd tends to struggle on a Treadmill due to the speed variations. Runn is also a convenient approach, and if you took the time to calibrate your treadmill, you could add the calibration factor into most running watches. The Runn also measures incline, though I'm not sure what software would support that measurement. I'd love to have incline data from my treadmill runs, but it may require a custom [[Connect IQ]] data field.